Boost Performance UK - Blueprinted corvette camaro ls1 ls6 engines, ls1 performance parts-custom, ford and scorpio specialists, rover, zetec, turbo engines. We specialise in custom built, Chevrolet LS1, Rover V8, Ford Zetec and Ford 24v Cosworth. 

Products > Rover V8 Turbo - Forced induction.

Rover V8 5.0 to 5.5 Litre Stroker Crankshaft
"IT FITS CROSS-BOLTED ENGINES."






We have over 20 years of experience with these engines but this is our favourite normally aspirated conversion. The crankshaft we developed can be machined to fit any Rover cylinder block, early or late but is specifically designed for the cross-bolted engines. This crankshaft is cross-drilled for enhanced lubrication to the rod bearing shells. It also has the 'long-nose' (can be shortened) found on the later engines fitted with the high volume G-rotor oil pump and serpentine front cover assembly. It features additional counterweights opposite rods numbered 4 & 5 to allow more precise balancing for higher rpms. The counterweights themselves have reduced diameter to clear the piston skirts on the down stroke. We modified our crankshafts to accept Chevrolet con rods and they can be bought from the USA quite cheaply. If your 3.9 litre and upwards engine which has the 94/96 mm bore size is tired or worn then this conversion may be suitable for you.

For turbocharged use and fitted with low compression Buick 300 cylinder heads this conversion could produce in excess of 550 lbs/ft of torque from 2500 rpm whilst keeping within sensible rpm limits and retaining the stock factory hydraulic lifters and valvetrain! Or we could build a low compression turbo engine using our own design of forged pistons and your existing cylinder heads to achieve similar goals.

Stroker fully counter-balanced crankshaft. We can supply an unmachined casting at short notice which you can have machined yourself.

PRICE: £450

A commonly available stock rover crankshaft is 82mm stroke and from this we can build 4.5l to almost 4.8l using crossbolted blocks. This keeps costs down and allows a reasonable compression ratio to be used, enquire.

PRICE: £POA

Turbo or Supercharged - Forced Induction Package.

Any compression possible depending on how much power you want. Dynamically re-balanced crankshaft/rotating assembly & blueprinted internals included as a part of this package. We cater for 3.9, 4.0, 4.5, 4.6, 5.0 litre and larger engines including all TVR variants. Turbo or supercharged short engines rebuilt for strength and durability using your block and crankshaft and our forged ultra strong, low compression pistons. We discard the weak cast Rover pistons as they are unsuitable for high cylinder pressures and are prone to cracking. Our replacement pistons feature forced pin oilers, ceramic heat treatments on the crowns, deeper valve cut outs, low friction anti-scuff side skirt coatings, gas accumulator grooves, reinforced ring lands and taper wall high strength gudgeon pins plus a top quality 'file to fit' Total Seal gapless piston ring set. We install top quality heavy duty bearing shells for the con-rods and main bearings and include an ARP stud kit to hold the bottom end together.

PRICE: £3,700

Long Turbo engines available.

Various specifications and options available to suit your requirements, including custom manufactured forged steel con-rods. Custom inlet manifolds, fabricated aluminium chargecoolers and cast iron exhaust headers. We can also fabricate steel tubuler headers. AJP's considered to.

PRICE: POA

Hot News! Coming soon, a TVR V8 single turbo conversion for appx 2000 (mapping not included). There will be several turbo options, tailored to suit engine capacity and performance requirements. The turbo and custom manifold will replace the exhaust 'Y' piece and development is nearly concluded. We can also offer a TT conversion as a viable and cheaper alternative to installing a Chevrolet engine. You also get to keep your gearbox and ancilliary parts thus saving money.

Rover V8 & LS1 Engine Blocks for Comparison.

 
Rover V8 Tall port Turbo Manifold MK2.









Mk2 Twin Turbo Manifolds, new tall port design for ported heads ie: TVR or Buick 300 cylinder heads. These manifolds feature bigger taller ports for increased exhaust flow and are adaptable for different turbo's and engine bays. A TVR conversion will be coming shortly. One manifold can be purchased for a single turbo conversion. Price per pair.

PRICE: £500. Or we can supply unmachined castings for you to machine locally or diy for £350.